Improve Pulmonary Outcomes
Individualized support of pulmonary outcomes based on specific clinical conditions of the patient thanks to frame-based lateral tilt guided by Electrical Impedance Tomography.
Multicare X
LINET's premium ICU bed Multicare X with unique frame-based lateral tilt.
Accompanied by Opticare X, innovative constant low pressure supporting surface.
- 063% Lower limb load reduction in patient mobilization thanks to Mobi-Lift (1)
- 095% Satisfaction with the new Opticare X Prone Mode (2)
- 067% Decrease in force needed to turn the patient with lateral tilt (1)
Discover effects of lateral tilt
Enhanced patient outcomes
Early mobilization
Our unique early mobility program with unique features, such as microshifting and Mobi-Lift handle, helps patients recover earlier and save signifcant cost to the hospital.
Pressure Injury Prevention
The new generation of the Opticare X mattress brings advanced premium pressure care with Optimal Immersion, microclimate management and with a mode that supports prone nursing (following prone nursing protocols, including the use of pillow/supports).
Falls Prevention
Multizone bed Exit Alarm, i-Brake or Opticare X are just a few of the safety features reducing the likelihood of patients falling.
Improve patient experience
Ensuring patients' physical and mental satisfaction for faster recovery thanks to features such as Opticare X Mobile Mode, Ergoframe, Electrical Bed Extension or ergonomic patients' controls.
Improved caregiver & hospital workflow
Safe patient moving & handling
Frame-based lateral tilt allows easier patient manipulation and minimizes back pain.
Easy patient transportation
30% lighter bed frame and motorized 5th castor for easier transportation.
Simplify caregiver procedures
Nurse-friendly interface of the bed makes frequent and critical nursing tasks simpler. 10“ Multiboard X display is easy to use and CPR features will provide aid in critical situations.
Hospital operations efficiency
Our Smart Care solutions, such as SafetyPort and SafeSense, reduce administrative tasks and make the hospital operations more efficient.
Recommended surfaces
New
Opticare X: Fully-Integrated Solution with Optimal Immersion
The new generation Opticare X mattress brings advanced premium pressure care with Optimal Immersion and microclimate management with ability for prone nursing.
-
Optimal Immersion
Pressures reduce as the patient becomes more immersed and enveloped into the mattress. At some point the patient will reach an optimal point where peak pressures are minimized. -
Microclimate Management
Opticare X helps maintain the natural thermoregulation by circulating air through the mattress surface. It helps to maintain healthy heat and moisture levels at the patient’s skin. -
Prone Nursing
Prone mode is using a higher level of air than other therapeutic modes providing a balance between pressure redistribution and stability for patients being nursed in a prone positions (prone positioning support recommended).
Virtuoso PRO: High-End Solution for Prone Nursing & Wound Offloading
Premium 3-cell alternating pressure mattress replacement reduces pressure and help to minimize pressure peaks to the patient's body with effect reffered as zero pressure.
-
3-cell Alternating System with Zero Pressure
Virtuoso 3-cell alternating mattress provides deflation of only one in three cells at any given time. This is referred to as ‘zero pressure’ -
Microclimate Management
Virtuoso PRO helps to maintain healthy heat and moisture levels at the patient’s skin. -
Prone Nursing & Wound Offloading
Virtuoso Pro 3-cell alternating mattress enables offloading of risk areas pressure pressure points by the manual deflation individual air cells.
Clinical and training materials
Clinical materials
Assessment of load on patients using Mobi-Lift
Assessment of load on personnel using Lateral Tilt
Targeted lateral positioning decreases lung collapse and overdistension in COVID‑19‑associated ARDS
Optimal Immerssion Clinical Guide
Pressure Care Terminology Guide
Early Mobilization with LINET
Early Mobilization Workflow
User experience with Multicare and Lateral Tilt
Product videos
Brochures
Technical information about Multicare X
Features
Automatic Lateral Therapy
The Multicare X Automatic Lateral Therapy is frame-based, can be programmed to perform cycles according to individual needs.
Lateral tilt
Patient's feet can touch the floor and reach the nose over toes position thanks to lower bed height achieved by tilting.
Combined tilting for postural drainage procedure
Thanks to combination of revTR and lateral tilt airways hygiene (postural drainage) can be easily performed as a part of respiratory therapy.
Opticare X prone mode
New Opticare X mode allows you to select a setting designed to aid prone nursing which is used more and more for respiratory conditions.
Opticare X mobile mode
Mobile Mode allows the mattress to be ‚stepped down‘ to a lower level of immersion to aid Comfort and independent movement for more mobile patients.
Opticare X Zoned Cover
Zoned cover designed to keep the centre of the mattress slippery with more "grippy" sides facilitating safe patient transfer.
Mobi-lift handle
Patient can hold onto the Mobi-Lift handle while sitting at the edge of the bed or attempting to stand.
i-Drive Power
Unique sensor against self-activation Intelligent accelerator for optimimalization of the drive speed.
IV & Drive
Combination of foldable IV poles and i-Drive controller.
Automatically engaged i-Brake
GO' mode helps keep the bed in straight direction → mitigation of required effort.
Multiboard x ergonomically positioned at 30° hob
New 10“ screen with intuitive controls makes daily nurse tasks easier.
USB integration
Patient can use charging directly from the bed‘s headside rail - no need to disconnect smartphone during transport.
Electrical bed extension
Electrically extended bed with surface contributes to comfort for tall patients.
Vascular Leg
The Vascular position allows the patient to begin early weight-bearing exercises.
Autocontour (Ergoframe)
Patient is less likely to slide down in bed by elevating the back rest and thigh rest together. Caregivers don't need to pull up patient back.
Orthopnoeic chair
Orthopnoeic Chair is the full chair position used for hemodynamic and muscle training.
Reverse Trendelenburg
In the reverse Trendelenburg, the patient is able to do weight-bearing exercises that are necessary for the patient to be able to stand up or walk.
Trendelenburg
The Trendelenburg position can be used in critical situations or to prevent air embolism during CVC placement. It is one of the one-button functions on Multicare X.
Foot controls
Caregiver has free hands and can be fully focused on the patient thanks to foot controls.
Siderails constant gap
Unique concept of Multicare X siderails: 45 cm height, Safety double mechanism, Smooth release by SoftDrop, Siderails down sensors and Constant gap.
30° hob stop & handles in headside rails
Siderails provides support during mobilization steps – moving patient to the edge of the bed, providing sit-to-stand support.
Patient controls ergonomy
Patient can easily reach bed controls while sitting or lying ergonomically.
Nurse call
Patient activates the nurse call comfortably from the bed, no need to reach any distant device.
X-ray cassette holder
Allows easy cassette insertion, adjustment and removal, without the need to reposition the patient.
Opticare X X-ray sleeve
For easier X-ray procedure and wide variety of cassettes.
CPR Electrical Button
CPR button flattens and lowers the bed, and deflates mattress.
CPR Handle
Quickly lowers the backrest to flat position.
Mattress Valve
Deflates the mattress quickly.
Accessories
IV&drive - foldable handles with i-Drive power holder.
Kit of stabilizing pads Advanced for the lateral tilt
Pair of protectors
Ventilator circuit holder
Tech specs
- External Dimensions in Standard Bed Position (length x width)
- 215 cm x 105 cm
- Safety Siderail Height above Mattress support platform
- 45 cm (maximum)
- Bed Extension
- 0 cm - 22 cm
- Maximum Dimensions of Mattress (length x width)
- 214 cm x 87,5 cm
- Maximum Mattress Height
- 23 cm
- Clearance in Standard Position
- 15 cm
- Minimum-Maximum Mattress support platform Height above floor (without Mattress)
- 44 cm - 82 cm
- Maximum Backrest Angle
- 70°
- Maximum Thighrest Angle
- 30°
- Maximum Calfrest Angle
- 38°
- Maximum Lateral Tilt Angle
- +30°/-30°
- Trendelenburg Angle
- 13°
- Antitrendelenburg Angle
- 16°
- Bed Safe Working Load (SWL)
- 250 kg
After-sales services
Smart Care
LINET's solution is not limited to beds and mattresses. We also provide our customer with smart technologies to address data management or patient monitoring. Discover LINIS SafetyPort, application for automated export of data from Multicare X.
Rental
LINET Rental services is a flexible, agile and complex solution adaptable for each individual organization. Our Rental solution allow our customers to get innovative therapy systems including Multicare X without direct purchase.
After Sales
We understand that safety and reliability are a priority in medical facilities. That is why, together with Multicare X, we offer a completely carefree warranty and post-warranty service that includes preventive maintenance, spare parts and repairs. All provided by our team of trained professionals.
Get in touch
and learn more about
Multicare X
Multicare X will be available for ordering on selected markets from October 2021.
Contact our customer advisor for more information
(1) Lebeda T et al., NRU for Occupational Physiology and Psychophysiology, Report no: 3636/2021, ex. 210347
(2) LINET Group, Multicare X and Opticare X Field test results – users evaluation 2021, internal document 2021_08. When rating the balance between pressure care and support needed for prone nursing, as evaluated by 71 caregivers.